Calculated-industries 4095-C User Guide Uživatelský manuál

User’s GUide — 1PIPE TRADES PRo™Advanced Pipe Trades Math CalculatorUSER’S GUidEModel 4095

User’s GUide — 11Weight/Volume Functions  Weight/Volume – Stores a new weight volume as pounds per cubic feet or other format as shown below. Def

12 — PiPe Trades Pro™Pipetting Project Keys TravelSlopeOffsetAngleº Enters or calculates a linear Slope, Slope Angle, or Percent Grade. The linear

User’s GUide — 13 Denes the Pipe Material. (Steel, Stainless Steel, Brass, Aluminum, Cast Iron, PVC or Copper). Elbow Type – Denes the type of

14 — PiPe Trades Pro™Miscellaneous Functions  Open parenthesis key Close parenthesis key Enters an exponential value other than x2 or Square Roo

User’s GUide — 15PREfEREncE SETTinGSHOW TO SET PREFERENCESThe following sections detail Preference Setting options for the Pipe Trades Pro calculator.

16 — PiPe Trades Pro™Second press of  : (Area displays) AREA Std. AREA 0. SQ FEET AREA 0. SQ INCH AREA 0. SQ M (repeats options)

User’s GUide — 17EnTERinG dimEnSionSLinear DimensionsWhen entering feet-inch values, enter dimensions from largest to smallest — feet before inches, i

18 — PiPe Trades Pro™EnTERinG convERSionSLinear ConversionsConvert 10 feet 6 inches to other dimensions, including metric:KEYSTROKE DISPLAY   

User’s GUide — 19KEYSTROKE DISPLAY 0.  5 CU FEET7 (Pounds) 312.1398 LB  (Kilograms) 141.5842 KGConvert a cubic meter of concrete to pounds

20 — PiPe Trades Pro™Flow Rate ConversionsYou can enter a Flow value in cubic feet per second, liters per second, cubic feet per minute, or gallons pe

User’s GUide — 3Designing and building new calculators like the Pipe Trades Pro™ Advanced Pipe Trades Math Calculator and the PlumbingCalc™ Pro Flow &

User’s GUide — 21baSic maTH oPERaTionSAdding and Subtracting Strings of DimensionsAdd the following measurements:• 6 feet 2-1/2 inches• 11 feet 5-1/4

22 — PiPe Trades Pro™ PERcEnTaGE calcUlaTionSThe  keys can be used for nding a given percent of a number or for working add-on, discount or divisio

User’s GUide — 23mEmoRy oPERaTionWhenever the  key is pressed, the displayed value will be added to the Memory. Other memory functions:FUNCTION

24 — PiPe Trades Pro™Using Memory Storage Keys (M1 - M9)In addition to the standard cumulative Memory (as previously described), your calculator has n

User’s GUide — 25PaPERlESS TaPEThe Paperless Tape allows you to display and review the last 30 entries of a calculation.   accesses the tape mo

26 — PiPe Trades Pro™calcUlaTE coSTSThe Cost function provides the total cost for material, based on a stored unit cost and an entered quantity of mat

User’s GUide — 27USinG THE PiPE TRadES PRoPipe Material KeyThe Pipe Material key lets you choose a pipe material, which denes the available sizes and

28 — PiPe Trades Pro™ (Schedule 80) TYPE 80 PLAStIC (Schedule 120) TYPE 120 PLAStIC (SDR 21) TYPE SD21 PLAStIC (SDR 26) TYPE SD26 PLAS

User’s GUide — 29 (Material) MATL SIZE StEEL (Weight per Foot) PIPE SIZE 10.2528 LB PER FEET (Filled Weight/Foot) FILL SIZE 13.11634 LB PER F

30 — PiPe Trades Pro™Butt Weld – ShortUse this option when utilizing 90° short radius or factory 45° short radius ttings, or any odd-angle short radi

4 — PiPe Trades Pro™ PiPe Trades Pro™The Pipe Trades Pro™ Advanced Pipe Trades Math Calculator has been specically designed for today’s pipe trade pr

User’s GUide — 31KEYSTROKE DISPLAY  0.1. Enter Offset:2 4   OFST 24 INCH2. Enter bend angle:4 5  /_Ø 45.00°3. Find the pipe length:

32 — PiPe Trades Pro™Simple Offset – Cut LengthFind the cut length (end-to-end) for a pipe offset with a 10” Offset and a 12” Run. The bend angle is u

User’s GUide — 33 TO 3-1/4 INCH GAP 0 INCH FIT° 39.81° IARC 3-15/16 INCH CARC 6-1/4 INCH OARC 8-9/16 INCHThe cut length

34 — PiPe Trades Pro™KEYSTROKE DISPLAY  ALL CLEArEd1. Enter Offset:2 4   OFST 24 INCH2. Enter bend angle:4 5  /_Ø 45.00º3. Enter the Ro

User’s GUide — 352. Enter the advance:2    (Advance) RUN 28 INCH3. Enter the Roll and calculate the pipe length and unknown bend angle:6  1 

36 — PiPe Trades Pro™KEYSTROKE DISPLAY  ALL CLEArEd1. Enter Pipe Size:6   STD SIZE 6 INCH2. Change the default Welder’s Gap from 1/8” to

User’s GUide — 37Concentric Pipe Bend CutbackFind the pipe Cutback when you are running pipes through a 45º bend with a 10" offset.10”CUTBACK45ºK

38 — PiPe Trades Pro™Calculate Take-Out and Butt Weld Elbow Cut MarksThe Take-Out function can be used to quickly solve a Take-Out and butt weld elbow

User’s GUide — 39Cut Length – Known Take-Out ValueThe Pipe Trades Pro can solve cut lengths for materials and ttings not currently built into the cal

40 — PiPe Trades Pro™Combination Rolling OffsetUnlike a regular rolling offset, the entry and exit ttings for a combination rolling offset are on dif

User’s GUide — 5TablE of conTEnTSGETTING STARTED ... 7Order of Operations ...

User’s GUide — 41a triangle is formed which will allow for an easy solution of the exit tting angle in step 2.0’ -39” 15/16TRAVEL0’ - 15”RUNUnknownEx

42 — PiPe Trades Pro™Horizontal to HorizontalIn the next example, the same box dimensions are used except the exit tting now creates a pipe exit hori

User’s GUide — 43Calculating DropIf a pipe Run requires 1/8" drop per foot for drainage, how much total drop is required for a 25' Run?KEYST

44 — PiPe Trades Pro™KEYSTROKE DISPLAY  ALL CLEArEd1. Enter the Velocity:   (Velocity) FPS 5.2. Enter the Area:       (Area) AR

User’s GUide — 45  (Cubic Feet per Minute) CFM 0.668403  (Cubic Feet per Second) CFS 0.01114  (Liters per Second) L/S 0.315451VelocityYou

46 — PiPe Trades Pro™KEYSTROKE DISPLAY  0.   M/S 0.If you know the velocity, you can convert to other dimensional units. KEYSTROKE

User’s GUide — 47 inHG PER FEET 0.000417 HEAD PER FEET 0.000472 BAR PER FEET 0.000014 KPA PER FEET 0.001411 PSI PER FEET 0.00

48 — PiPe Trades Pro™Pressure/ForceIf you know the Force and Area, you can calculate Pressure and convert the solution to different units of Pressure.

User’s GUide — 49Pipe CapacityHow many gallons of water will a 20' long 6" pipe hold?KEYSTROKE DISPLAY  0.1. Enter the Pipe Size:  ST

50 — PiPe Trades Pro™Find the weight of the same length of pipe lled with ethanol (one gallon of ethanol weighs 6.59 lbs.) Do not clear previous keys

6 — PiPe Trades Pro™Simple Offset - Known Bend Angle ... 30Simple Offset - Unknown Bend Angle ...

User’s GUide — 51Circle Area and CircumferenceFind the area and circumference of a circle with a diameter of 25 Inches:KEYSTROKE DISPLAY  0.2 5 

52 — PiPe Trades Pro™Given side A and angle a, find: Side C A  a   (e.g.,    5   1    ) Side B A  a   Angle b 90°  a

User’s GUide — 53 aPPEndix a – Pipe Material, Pipe Type And Data TablesAfter selecting a Pipe material, you can select Pipe Types for that material a

54 — PiPe Trades Pro™ aPPEndix b – Default SettingsAfter a Clear All (  ), your calculator will return to the following settings:Stored Values

User’s GUide — 55 aPPEndix c – Preference SettingsThe Pipe Trades Pro has Preference Settings that allow you to customize or set desired dimensional

56 — PiPe Trades Pro™3) Volume Display Format – *Standard (if units entered are the same — e.g., Feet x Feet x Feet — the answer will remain in this

User’s GUide — 57 aPPEndix d – ConstantsFor material surface roughness, we use the following:MaterialPVC Copper Steel (low carbon)Stainless Steel (au

58 — PiPe Trades Pro™ aPPEndix f – Accuracy/Errors, Auto Shut-Off, Batteries, ResetAccuracy/Errors Accuracy/Display Capacity — Your calculator has a

User’s GUide — 59Batteries The Pipe Trades Pro uses two LR-44 batteries.Replacing BatteriesShould your calculator display become very dim or erratic,

60 — PiPe Trades Pro™ aPPEndix G – FormulasArea Formulas

User’s GUide — 7GETTinG STaRTEdYou may want to practice getting a feel for your calculator keys by reading through the key denitions and learning how

User’s GUide — 61Surface Area/Volume Formulas

62 — PiPe Trades Pro™WARRANTY, REPAIR AND RETURN INFORMATION Return Guidelines1. Please read the Warranty in this User’s Guide to determine if your C

User’s GUide — 63Warranty Warranty Repair Service – U.S.A.Calculated Industries (“CI”) warrants this product against defects in materials and workmans

64 — PiPe Trades Pro™FOR A PARTICULAR PURPOSE. AS A RESULT, THIS PRODUCT, INCLUDING BUT NOT LIMITED TO, KEYSTROKE PROCEDURES, MATHEMATICAL ACCURACY AN

User’s GUide — 654840 Hytech DriveCarson City, NV 89706 U.S.A.1-800-854-8075 • Fax: 1-775-885-4949E-mail: [email protected]

Designed in the United States of America.Printed in China.04/12UG4095E-C

8 — PiPe Trades Pro™Using ParenthesesYour calculator has parentheses keys  and  for performing mathematical operations. (In the Order of Operations

User’s GUide — 9kEy dEfiniTionSBasic Function Keys  On/Clear Key – Turns on power. Pressing once clears the last entry and the display. Pressing twi

10 — PiPe Trades Pro™Dimensional Function Keys Feet – Enters or converts to feet as whole or decimal numbers. Also used with  and  keys for ente