Calculated-industries 6260 User Guide Uživatelský manuál

USER’SGUIDEAreaTake - Off Tooland Digitizing SystemModel#6260

GETTING STARTEDOnce assembly and setup are complete, proceed with the following steps in order to begin measuring.1. When placing the bars and securin

Right-Hand Confi guration ShownUSER’S GUIDE — 9

[END] Ends polyline measurement, displaying the total perimeter. Also ends the 2-Point Circle measurement when measuring a diameter, displaying the ci

[ON/CLEAR]Turns the unit ON and clearsthe display. Holding down the[ON/CLEAR] key for 1.5 seconds also powers the unit off. [CLOSE +]Completes the Pol

[UNDO]Undoes the previous measurement. Allows you to undo the last 10 measurements (if applicable) while in measure mode. If a measurement has been cl

[PC SEND]When connected to a PC, sends the value on the main display in decimal format to the PC (see PC Interface section). [ARC/CIRC]First press ide

[MODE]Used to select from the list of available modes (see Built-In Scales section).[SET] [MODE]Used to move back through the list of available modes.

[UNITS]Used to select from the list of available units of measurement (see Units of Measurement section).[SET] [UNITS]Used to move back through the li

The top legend displays the following:• SET• CIRC (Circle)• ARC• M (Memory)The Measure Status and number of sides are displayed here (End or Closed a

BUILT-IN SCALESThe following modes and scales are available for selection using the [MODE] and [SCALE] keys, depending on whether the puck is set to I

TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1SETUP . . . . . . . . . . . . . . . . . . .

SHAPES AND DEFINITIONSThe Ultra Scale Master Pro can measure Polylines, Polygons, regular or irregular shapes, Arcs and Circles based on the following

IRREGULAR SHAPEAn outline orsurface confi gurationof a formARC:A segment of a curveCIRCLE:A plane curve equidistant from a fi xed centerILLEGAL SHAPE:Th

12MEASURING POLYLINESOPERATING SEQUENCE1. Press the [ON/CLEAR] key twice to clear the display. Place the crosshairs over the fi rst point and press the

PERIMETERWALL AREA*HEIGHT*SIDE 1SIDE 24. Press the [END] key. The total Perimeter is displayed. Once a measurement is ended, press the D-Pad down [6]

MEASURING SIMPLE POLYGONSOPERATING SEQUENCE1. Press the [ON/CLEAR] key twice to clear the display. Place the crosshairs over the fi rst point and press

5. Press the [CLOSE+] key. The total Area is displayed. Once a measurement is closed, press the D-Pad down [6] to display Perimeter, Wall Area, Volume

MEASURING TAKE-OUTSOPERATING SEQUENCE1. Press the [ON/CLEAR] key twice to clear the display. Place the crosshairs over the fi rst point and press the [

AREAADJUSTED AREA5. Press the [CLOSE+] key. The total Area is displayed.*6. Press the [M+] key to store the Area in Memory, then repeat steps 1 throug

MEASURING COMPLEX POLYGONSOPERATING SEQUENCE1. Press the [ON/CLEAR] key twice to clear the display. Place the crosshairs over the fi rst point and pres

AREAPERIMETERWALL AREA*HEIGHT*VOLUME*SIDE 1SIDE 2SIDE 3SIDE 5SIDE 4SIDE 6SIDE 8SIDE 79. Press the [CLOSE+] key. The total Area is displayed. Once a me

INTRODUCTION The Ultra Scale Master Prohas been specifi cally designed for residential and light commercial builders and contractors requiring area and

MEASURING IRREGULAR SHAPESOPERATING SEQUENCE1. Press the [ON/CLEAR] key twice to clear the display. Place the crosshairs over the fi rst point and pres

AREAPERIMETERWALL AREA*HEIGHT*VOLUME*SIDE 1SIDE 2SIDE 3SIDE 5SIDE 4SIDE 6SIDE 8SIDE 79. Press the [CLOSE+] key. The total Area is displayed. Once a me

MEASURING ARCS AND CIRCLESDEFINITIONS: Listed below are defi nitions and illustrations of the Arc and Circle measurement results.ARC AREACHORD LENGTHCH

CIRCLE PERIMETERCIRCLE AREAHEIGHTCIRCLE PERIMETERCIRCLE AREACIRCLE DIAMETERCIRCLERADIUSHEIGHTCircle Volume – The total of the Circle Area multiplied b

MEASURING ARCSOPERATING SEQUENCE1. Press the [ON/CLEAR] key twice to clear the display. Press the [ARC/CIRC]* key once to enter Arc Mode. Place the cr

ARC LENGTHARC LENGTH WALL AREAARC AREAARC PERIMETERARC WALL AREA*ARC HEIGHT*ARC VOLUME*4. Upon pressing the [MEASURE] key in Step-3, the Arc measureme

MEASURING 3-POINT CIRCLESOPERATING SEQUENCE11. Press the [ON/CLEAR] key twice to clear the display. Press the [ARC/CIRC]* key twice to enter Circle Mo

CIRCLE RADIUSCIRCLE DIAMETER4. Upon pressing the [MEASURE] key in Step 3, the Circle measurement was automatically completed and the Circle Area displ

There are two methods for programming Custom Scales into your Ultra Scale Master Pro. “Measured Custom Scales” allow you to measure a specifi ed Length

5. The displayed units begin fl ashing, indicating that they are ready to be changed. Press [UNITS] to scroll through the available units.*6. Press D-P

SETUPPACKAGE CONTENTSYour package contains the following pieces:Female End Cap2 — ULTRA SCALE MASTER® PROLong Refl ector BarUSB CableUltra Scale Master

SETTING AN ENTERED CUSTOM SCALE (IMPERIAL MODE)1. Press [MODE] until “CUST” is displayed. Press [SCALE] to scroll through the four available Custom Sc

A Height can be set to calculate Wall Areas and Volumes which are displayed using the D-Pad once an area measurement has been completed. If no Height

UNITS OF MEASUREMENTThe following units of measurement are available for selection by pressing the [UNITS] key located under the slide cover door. You

DIGITIZER MODEThe Ultra Scale Master Pro can be used as a Digitizer to send measurement data (X,Y coordinates) and key press data to digitizing softwa

PC INTERFACEThe Ultra Scale Master Pro with PC Interface can be used to send displayed numerical values from your Puck directly to the selected estima

SENDING VALUES TO YOUR PC (PC SEND) The [PC Send] key sends the displayed value from the Puck to the selected software program on your PC. Values can

The following is an example of the results of a Polygon measurement, which include the Area, Perimeter, Wall Area, and Volume.In the fi rst column are

1. MEASUREMENT DISPLAY:Total* – Displays the accumulated total of all measured segments.Side – Displays only the last measured segment.2. BEEP:On*

5. PC SEND TERMINATING COMMAND:Enter* – Performs an ENTER command after value is sent to the PC.Tab – Performs a TAB command after value is sent to

APPENDIX A APPENDIX BACCURACY/ERRORS/AUTO SHUT-OFFAccuracy/Display Capacity – The Ultra Scale Master Prohas a seven-digit main display, while maintai

User’s Guide,Quick Reference Guide,and Quick Setup SheetMale End CapUSER’S GUIDE — 3Short Refl ector BarLong Refl ector BarCarrying Case

APPENDIX C APPENDIX DSPECIFICATIONS REPAIR AND RETURNWARRANTY, REPAIR AND RETURN INFORMATIONReturn Guidelines1. Please read the Warranty in this User

RIGHT-HAND ASSEMBLYAssemble the refl ector bars as shown. Align the corner connector at a 90° angle at the top left corner of the plans.5. Slide Female

4. Insert the Male End Cap into the female end of the Short Refl ector Bar. The Male End Cap is preinstalled for a Right-Hand confi guration.3. Insert t

NOTE: Sloping side of the Refl ector Bars face outward.5. Insert the the male end of the second Long Refl ector Bar into the female end of the Short Refl

FINAL ASSEMBLYThe ultrasonic beams are sent from the right arm of the Puck to the top bar, then refl ected back, and from the left arm of the Puck to t